OWNER’S MANUALCL1000 Ceiling LightMarus11727 Fruehauf DriveCharlotte, NC 28273 USA
812”12”18”18”MOUNTING LOCATIONFOR RIGHT-HANDEDOPERATORMOUNTING LOCATIONFOR LEFT-HANDEDOPERATORTYPICAL POSITION OF CEILING MOUNTIN RELATION TO DENTAL C
91 INCHCEILING JOISTS16” O.C.POWER SUPPLYCONDUITFINISHED CEILINGMATERIALMOUNTING PLATEw/ COLLARPOWER CONDUIT COMES THROUGH HOLE 2-1/2” OFFSET FROM CEN
10CEILING JOISTFIXED CEILINGSUSPENDEDCEILINGSUSPENDEDCEILINGCOVERCOVERMOUNTING PLATEw/ COLLAR & POSTMOUNTING PLATEw/ COLLAR & POSTSUGGESTED IN
11Metal Structure for Suspended CeilingElectrical RequirementsThe 115VAC/230VAC service line for the ceiling light should be evaluated and installed b
12Ceiling Light Installation Instructions Although traditional methods dictate mounting the light to the left side of the chair for a right-han
1311. Check the light for freedom of movement and for any drift when positioned. Recheck the post and make any necessary leveling adjustments. Raise t
14Power SupplyAccess HoleJunction BoxPost SocketSuspension Tube orCeiling Post(Refer to chart on Pg. 4)GroundTerminalSafety BoltCeiling MountingPlateC
15Overview / Replacement PartsControlsThe on-off switch is located on the control panel directly above the light reector. The long toggle provides
16 Turn 1/8 Clockwise to lock - logo should be level TetherAdjustmentsBulb Removal and ReplacementNote: For maximum reliability and optimum operation
17Light Focus AdjustmentsNote: Focus adjustment should be checked each time a new bulb is installed.1. Place a white paper or cardboard sheet in fron
Marus11727 Fruehauf DriveCharlotte, NC 28273 Printed in the U.S.A. 70-050R228 Rev 11 02/12Technical SupportTech Support: 800-304-5332FAX
18Yoke Pivot Friction AdjustmentHorizontalNote: If the light head pivots too freely horizontally, an adjustment can be made as follows:1. Remove the
19Flex Arm AdjustmentVertical1. Remove the two ex arm cover screws using a at head screwdriver. (See gure 15).2. Remove the ex arm cover.3. Usi
20ELECTROMAGNETIC COMPATIBILITYElectrical medical devices are subject to special EMC safety measurements and as a result the equipment must be install
21This product is intended for use in the electromagnetic environment specied below. The customer or the user of this product should ensure that it
22NOTE 1: At 80 MHz to 800 MHz, the higher frequency range applies.NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagati
23Guidance and manufacturer‘s declaration-electromagnetic emissionsThis product is suitable for use in all establishments, other than domestic establi
24Electrical SchematicsCL1000 Ceiling Light - 115V 0V115V230V
25Electrical SchematicsCL1000 Ceiling Light- 230V 230V115V0V
26Verify the following after installation or servicing of the light: All manuals are present. All labels are present and legible. No mechanical dam
1Table of ContentsGeneral Information ...
29Purchase InformationNotes / Service HistoryWrite in the model and serial numbers below for all applicable equipment such as the chair, unit light an
70-050R228Rev. 11 •02/12Marus11727 Fruehauf DriveCharlotte, NC 28273 USATechnical support: 800-304-5332Web Site: www.marus.com
2The following symbols may be used throughout this manual:CAUTION. Failure to carefully follow the described procedure may result in damage to the eq
3Storage Conditions:-55°C to +50°C10% to 90% Relative HumidityThe pre-installation must be performed according to the requirements in our ‘Pre-install
4Technical InformationTechnical Specications for the Dental LightTechnical Description — LightThe dental light is used for illuminating the oral cav-
5WARNINGS, DISINFECTING & STERILIZATION - LIGHTSInfection control in the dental ofce continues to be a high priority for our customers and end us
6CLEANING YOUR LIGHTCleaning Reector and CoverNOTE: Use only denatured alcohol to clean the glass reector. Use only mild soap and water to clean th
712”23 1/2”21-1/2” - 26”28”TRAVELDimensionsLocationA typical location for mounting the ceiling mount light is relation to the dental chair for a right
Komentarze do niniejszej Instrukcji